建立自己的躺式自行车（二十一）
建立自己的躺式自行车（二十）
最后的组装和调整
Procedure Overview 程序概述
This chapter is a catchall for all open items that were not performed in previous chapters. These include the fabrication of the Derailleur Cable Stop, and drilling the holes for both steering knuckle levels. In addition, final assembly instructions including front-end adjustments have been included. 本章是在以前的章节统称为所有打开的项目进行了不。这些措施包括停止生产的变速器电缆，钻两个孔，关节指导的水平。此外，总装的指示，包括前端的调整已包括在内。
Tools Required 所需的工具
9/16" socket 9 / 16“插座
9/16" wrench 9 / 16“扳手
Adjustable crescent wrench 可调月牙扳手
5 mm hex key (Allen wrench) 5毫米六角键（扳手）
Wooden or rubber mallet 木制或橡胶槌
Whiskey 威士忌酒
Assumptions 假设
· · You are not an idiot (even if your wife thinks so). 你是不是傻子（即使你的妻子这样认为）。
· · The front wheels have been laced using a two cross pattern. 前轮股价已使用两型交叉。
· · You have the following components: 您有以下内容：
· · Front and rear derailleur, ATB type, STX RC or better 前后变速器，全地形类型，stx基因钢筋混凝土或更好
· · A rear 26" inch wheel with cluster 阿后26“英寸轮与集群
· · Brake handles 制动手柄
· · Handle grips 手柄握把
· · Shifters, Bar Cons suggested 转换器，酒吧缺点建议
· · Cables, derailleur, brakes 电缆，变速器，制动器
· · Three lengths of chain 三链的长度
· · Bottom bracket, UN51 or better 底部支架，UN51或更好
· · Set of cranks w/chain rings, Forged, triple ring 瓦特集曲柄/链环，锻造，三环
Lacing the Front Wheels 鞋带前轮
Lace the front wheels using a two cross pattern. 花边图案的交叉使用两个前轮。 The spoke size is dependent on the type of rim. These spokes are generally 168 mm in length. 在谈到大小是依赖于边缘的类型。这些辐条长度一般一六八毫米英寸 This assumes an ERTO 405MM rim. 这是假设一埃尔托405MM边缘。
Completing the Steering Control System 完成转向控制系统
Each Steering Knuckle is attached to the trike frame cross members using two 3/8" Rod End Bearings. Each of these rod bearings is attached to the ends of the kingpins. On the open threaded end of each rod bearing, place a 3/8"-24 TPI jam nut followed by a 3/8" washer. Situate the steering knuckle assembly so that it fits on to the cross member knuckle back plate. Adjust the jam nuts on both rod bearings so that the axles are perpendicular (at a right angle) to the ground. Perform this operation for the other steering knuckle as well. Place washers on the opposites sides of the knuckle back plates. Last, secure the assemblies by placing Nyloc lock nuts on all four rod bearing ends. Refer to the illustration below: 每个转向节相连的三轮车架横梁使用两个3 / 8“杆端轴承。轴承每个这些杆是连接到主销的两端轴承。杆在每个开放线程结束，地点1 3 / 8 “-24 TPI的防松螺母8后跟一个3 /”洗衣机。位于该转向节大会，以便它适合于板的横梁关节回来。两杆轴承调整螺母上的果酱，使轴是垂直的（在直角）执行此操作的其他转向到地面。关节以及。广场上的对立垫圈板两侧的关节回来。去年，安全杆轴承大会上通过将所有四个Nyloc锁螺母结束。参阅说明如下：
这篇文章刊登于(www.naf.com.cn),更多请参考以上网站.
最后的组装和调整
Procedure Overview 程序概述
This chapter is a catchall for all open items that were not performed in previous chapters. These include the fabrication of the Derailleur Cable Stop, and drilling the holes for both steering knuckle levels. In addition, final assembly instructions including front-end adjustments have been included. 本章是在以前的章节统称为所有打开的项目进行了不。这些措施包括停止生产的变速器电缆，钻两个孔，关节指导的水平。此外，总装的指示，包括前端的调整已包括在内。
Tools Required 所需的工具
9/16" socket 9 / 16“插座
9/16" wrench 9 / 16“扳手
Adjustable crescent wrench 可调月牙扳手
5 mm hex key (Allen wrench) 5毫米六角键（扳手）
Wooden or rubber mallet 木制或橡胶槌
Whiskey 威士忌酒
Assumptions 假设
· · You are not an idiot (even if your wife thinks so). 你是不是傻子（即使你的妻子这样认为）。
· · The front wheels have been laced using a two cross pattern. 前轮股价已使用两型交叉。
· · You have the following components: 您有以下内容：
· · Front and rear derailleur, ATB type, STX RC or better 前后变速器，全地形类型，stx基因钢筋混凝土或更好
· · A rear 26" inch wheel with cluster 阿后26“英寸轮与集群
· · Brake handles 制动手柄
· · Handle grips 手柄握把
· · Shifters, Bar Cons suggested 转换器，酒吧缺点建议
· · Cables, derailleur, brakes 电缆，变速器，制动器
· · Three lengths of chain 三链的长度
· · Bottom bracket, UN51 or better 底部支架，UN51或更好
· · Set of cranks w/chain rings, Forged, triple ring 瓦特集曲柄/链环，锻造，三环
Lacing the Front Wheels 鞋带前轮
Lace the front wheels using a two cross pattern. 花边图案的交叉使用两个前轮。 The spoke size is dependent on the type of rim. These spokes are generally 168 mm in length. 在谈到大小是依赖于边缘的类型。这些辐条长度一般一六八毫米英寸 This assumes an ERTO 405MM rim. 这是假设一埃尔托405MM边缘。
Completing the Steering Control System 完成转向控制系统
Each Steering Knuckle is attached to the trike frame cross members using two 3/8" Rod End Bearings. Each of these rod bearings is attached to the ends of the kingpins. On the open threaded end of each rod bearing, place a 3/8"-24 TPI jam nut followed by a 3/8" washer. Situate the steering knuckle assembly so that it fits on to the cross member knuckle back plate. Adjust the jam nuts on both rod bearings so that the axles are perpendicular (at a right angle) to the ground. Perform this operation for the other steering knuckle as well. Place washers on the opposites sides of the knuckle back plates. Last, secure the assemblies by placing Nyloc lock nuts on all four rod bearing ends. Refer to the illustration below: 每个转向节相连的三轮车架横梁使用两个3 / 8“杆端轴承。轴承每个这些杆是连接到主销的两端轴承。杆在每个开放线程结束，地点1 3 / 8 “-24 TPI的防松螺母8后跟一个3 /”洗衣机。位于该转向节大会，以便它适合于板的横梁关节回来。两杆轴承调整螺母上的果酱，使轴是垂直的（在直角）执行此操作的其他转向到地面。关节以及。广场上的对立垫圈板两侧的关节回来。去年，安全杆轴承大会上通过将所有四个Nyloc锁螺母结束。参阅说明如下：
这篇文章刊登于(www.naf.com.cn),更多请参考以上网站.
One Response to “建立自己的躺式自行车（二十一）”
Leave a Reply
发表评论:
◎欢迎参与讨论，请在这里发表您的看法、交流您的观点。